Differential LVPECL Clock Oscillator
  CXO5032PK2.5,  2.5V, 0.2pS Jitter, non PLL

  • SMD in ceramic case (5.0 x 3.2 x 1.2) mm
  • Tri-State Enable / Disable   on pad No. 1
  • Femto second integrated phase jitter 
    (200 fs typical, 12 KHz to 20 MHz)
  • Superior phase noise (-135 dBc/Hz at 10 KHz and
     -142 dBc/Hz at 100 KHz offset)
  • RoHS conform;  Lead-free product; 
    on Tape (16mm) & Reel
  • Vibration: MIL-STD-202F method 204, 
                   35G, 50 to 2000 Hz
  • Shock:     MIL-STD-202F method 213B, 
                   test cond. E, 1000GG 1/2 sine wave
  • High performance with surprisingly low price
 Differential LVPECL Clock Oscillator CXO5032PK2.5
       
 LVPECL Square Wave Output Wave Form
Specifications
Holder Type: CXO5032PK2.5; 2.5V(Voltage code is "2.5"); Tri-State on pad 1
Frequency Range: 13.500 MHz  ~  220.000 MHz
Frequency Stability at 25°C: ±20 to ±100 ppm
Operating Temperature Range: -20°C to +70°C,   -40°C to +85°C
Storage Temperature: -55°C  to  +150°C
Power Supply Voltage (Vdd): + 2.5V  D.C.    ± 5%
Maximum Supply Current (15pF load): 30mA typical   50mA max.
Output Swing: 595 mV min; 750 mV typical; 930 mV max.
Output Logic Levels: High "1" Voh  Vdd-1.025V min., Vdd-0.95 V typical; 
Vdd-0.88V max. Condition: RL= 50 Ohm to (Vdd-2.0V)
Low  "0" VoL  Vdd-1.810V min., Vdd-1.70 V typical; 
Vdd-1.62V max. Condition: RL= 50 Ohm to (Vdd-2.0V)
Output Symmetry (Duty Cycle): 50% ± 5%max. measured at 50% waveform
Load: RL=50 Ohm into  (Vdd-2.0V) or
Thevenin equivalent (terminating resistors required on all outputs).
Rise/Fall Time: 0.5ns typical, 0.5ns max. @ 20% to 80% of PECL wave form
Start Up Time: 5 ms typical; 10 ms max.
OE Function Pin 1: Enable  ll When 70% min. of VDD to Enable Output. Enable time : 10 ms max.
Disable ll When 30% max. of VDD to Disable Output.
Disable current : 10 µA max. , Disable time : 0.2 µs max.
Phase Jitter (12 kHz to 20 MHz): 0.2 ps typical,  0.5 ps (max.), for 156.250 MHz, 3.3V
Phase Noise ( 156.250 MHz):   -50dBc/Hz @ 10Hz,    -80dBc/Hz @ 100Hz,   -115dBc/Hz @ 1kHz
-135dBc/Hz @ 10kHz, -142dBc/Hz @ 100kHz, -147dBc/Hz @ 1MHz,
-152dBc/Hz @ 10MHz
Aging: < ±3ppm max. for the first year
Reflow Condition: 260°C max for 10 sec.
Germany:   COMTEC CRYSTALS GmbH
Sultenstr. 12-14  ·  85586 Poing / GERMANY
Tel +49 8121 778160 · Fax +49 8121 778177
e-Mail     info@comtec-crystals.com
Internet  http://www.comtec-crystals.com
Subject to change without prior notice
TÜV ISO 9001COMTEC LOGO

Technical data and graphics are all
copyrighted (c) by Comtec Crystals Group
France:  COMTEC CRYSTALS SARL
23, rue du Faucon · 67500 Haguenau / FRANCE
  Tel +33 388 732162 · Fax +33 388 730118
e-Mail  sales@comtec-crystals.com
Internet  http://www.comtec-crystals.com
Sous réserve de modifications